Hanna-instruments HI 700 Series Manual de usuario descargar pdf (Pagina 8)

1514

Code Valid Values Default PW

14 Relay 1 deviation (D1) 0.5 to 10% f.s. 1% f.s. no

15 Relay 1 reset time 0.1 to 999.9 minutes 999.9 no

16 Relay 1 rate time 0.0 to 999.9 minutes 0.0 no

21 Relay 2 mode (M2) same as relay 1 0 no

22 Relay 2 setpoint (S2) 0.5 to 99.5% full scale 75% f.s. no

23 Relay 2 hysteresis (H2) 0 to 5% f.s. 1% f.s. no

24 Relay 2 deviation (D2) 0.5 to 10% f.s. 1% f.s. no

25 Relay 2 reset time 0.1 to 999.9 minutes 999.9 no

26 Relay 2 rate time 0.0 to 999.9 minutes 0.0 no

30 Relay 3 high alarm (HA) 0.5 to 99.5% full scale 95% f.s. no

HA-HysLA+Hys,Hys=1.5%f.s.,HAS1 or HAS2

31 Relay 3 low alarm (LA) 0.5 to 99.5% full scale 5% f.s. no

LA+HysHA-Hys,Hys=1.5%f.s.,LAS1 or LAS2

32 Proportional control 1 to 30 min 5 no

mode period

33 Maximum relay ON time 10 to 9999 min 60 no

(after which an alarm mode is entered)

34 Alarm mask time 00:00 to 30:00 00:00 no

40 Analog output selection 0: 0-1mA 2 no

1: 0-20 mA

2: 4-20 mA

3: 0-5 VDC

4: 1-5 VDC

5: 0-10 VDC

41 Analog output 0 to 100% full scale 0 no

lower limit (O_VARMIN) (O_VARMIN  O_VARMAX - 5% f.s.)

42 Analog output 0 to 100% full scale 100% f.s. no

upper limit (O_VARMAX) (O_VARMIN  O_VARMAX - 5% f.s.)

• After confirmation, the selected parameter

is displayed. The user can scroll through

the parameters by pressing CFM.

In order to directly set another param-

eter, press SETUP again and enter the

code or scroll to it by pressing CFM.

The following table lists the setup codes along with the descrip-

tion of the specific setup items, their valid values and whether

password is required to view that item (“PW” column):

Code Valid Values Default PW

00 Factory ID 0 to 9999 0000 no

01 Process ID 0 to 99 00 no

02 Control enable/disable 0: C.M. disabled 0 no

1: C.M. enabled

03 Range 1: 0.0-199.9 μS (or 100.0 ppm) 4 no

(depends on model) 2: 0-1999 μS (or 1000 ppm)

3: 0.00-19.99 mS (or 10.00 ppt)

4: 0.0-199.9 mS (or 100.0 ppt)

04 Reference Temperature 20°C or 25°C 25°C no

05 Temperature Coefficient 0.00 to 10.00 %/°C 2.00 no

06 Input Selection 0: conductivity probe 0 no

1: 4-20 mA input signal

07 Temperature ATC: Automatic ATC no

compensation User: Manual

08 TDS Factor (HI710 only) 0.00 to 1.00 0.50 no

11 Relay 1 mode 0: disabled 0 no

(M1) 1: ON-OFF high setpoint

2: ON-OFF low setpoint

3: PID, high setpoint

4: PID, low setpoint

12 Relay 1 setpoint (S1) 0.5 to 99.5% full scale 25% f.s. no

13 Relay 1 hysteresis (H1) 0 to 5% f.s. 1% f.s. no

1 2 3 4 5 6 7 8 9 10 11 12 13 ... 28 29

Comentarios a estos manuales

Sin comentarios

Hanna-instruments HI 700 Series Manual de usuario Pagina 8

Comentarios a estos manuales

Relacionado con productos y manuales para Instrumentos de medición Hanna-instruments HI 700 Series