Hanna-instruments HI 83200 Manual de usuario

1Instruction ManualHI 83200Multiparameter BenchPhotometerfor Laboratorieswww.hannainst.com

18 19• Remove the cap and fill the Demineralizer Bottle with tap water.• Replace the cap and shake gently for at least 2 minutes.• Open the upper part

20 21AluminumALUMINUMSPECIFICATIONSRange 0.00 to 1.00 mg/LResolution 0.01 mg/LAccuracy ±0.02 mg/L ±4% of reading at 25 °CTypical EMC ±0.01 mg/LDeviati

22 23• Add the content of one packet of HI 93712C-0 Bleachingpowder to one of the two cuvettes. Replace the cap and shakevigorously until completely d

24 25Ammonia MRSPECIFICATIONSRange 0.00 to 10.00 mg/LResolution 0.01 mg/LAccuracy ±0.05 mg/L ±5% of reading at 25 °CTypical EMC ±0.01 mg/LDeviationLig

26 27• Remove the cuvette.• Add 4 drops of HI 93715A-0 First Reagent (6 drops forseawater analysis). Replace the cap and mix the solution.• Add 4 drop

28 29Ammonia LRBromineBROMINESPECIFICATIONSRange 0.00 to 8.00 mg/LResolution 0.01 mg/LAccuracy ±0.08 mg/L ±3% of reading at 25 °CTypical EMC ±0.01 mg/

30 31• Remove the cuvette and add the content of one packet ofHI 93716-0 DPD reagent. Replace the cap and shake gently forabout 20 seconds to dissolve

32 33FREE CHLORINEFREE CHLORINEFREE CHLORINEFREE CHLORINEFREE CHLORINESPECIFICATIONSRange 0.00 to 2.50 mg/LResolution 0.01 mg/LAccuracy ±0.03 mg/L ±3%

34 35• Reinsert the cuvette into the instrument.• Press Read to start the reading. The instrument displays the results in mg/L of free chlorine.INTERF

36 37Total Chlorine• Press the Zero key. The meter will show “-0.0-” when the meter is zeroed and ready for measurement.• Remove the cuvette.Powder re

2 3PRELIMINARY EXAMINATIONPlease examine this product carefully. Make sure that the instrument is not damaged. If any damageoccurred during shipment,

38 39Chlorine DioxideCHLORINE DIOXIDESPECIFICATIONSRange 0.00 to 2.00 mg/LResolution 0.01 mg/LAccuracy ±0.10 mg/L ±5% of reading at 25 °CTypical EMC ±

40 41Chlorine Dioxide• Press the Zero key. The meter will show “-0.0-” when the meter is zeroed and ready formeasurement.• Fill another cuvette with 1

42 43• Reinsert the cuvette into the instrument.• Press Timer and the display will show the countdown prior to the measurement or, alternatively, wait

44 45• Reinsert the cuvette into the instrument.• Press Timer and the display will show the countdown prior to the measurement or, alternatively, wait

46 47Color of Water• Fill the second cuvette up to the mark with unfiltered sampleand replace the cap. This is the apparent color.• Filter 10 mL of sa

48 49Copper HR• Remove the cuvette.• Add the content of one packet of HI 93702-0 Bicinchoninate.Replace the cap and shake gently for about 15 seconds.

50 51Copper LR• Remove the cuvette.• Add the content of one packet of HI 95747-0 Bicinchoninate.Replace the cap and shake gently for about 15 seconds.

52 53Cyanuric Acid• Add the content of one packet of HI 93722-0 Cyanuric AcidReagent. Replace the cap and shake gently for about10 seconds (dissolutio

54 55• Press Timer and the display will show the countdown prior to zeroing the blank or, alternatively, waitfor two minutes and press Zero. The displ

56 57Hardness Ca• Add 1 drop of HI 93720C-0 EGTA solution to one cuvette (# 1), replacethe cap and invert the cuvette several times to mix. This is th

4 5PRINCIPLE OF OPERATIONAbsorption of light is a typical phenomenon of interaction between electromagnetic radiation and matter.When a light beam cro

58 59 Hardness MgMAGNESIUM HARDNESSSPECIFICATIONSRange 0.00 to 2.00 mg/LResolution 0.01 mg/LAccuracy ±0.11 mg/L ±5% of reading at 25 °CTypical EMC ±0.

60 61Hardness Mg• Press s or t to access the second level functions.• Press the Chem Frm key to convert the result in mg/L of Magnesium (Mg).• Press t

62 63• Add 12 drops of the HI 93704-0 reagent toeach cuvette. Replace the caps and shakegently to mix (about 30 seconds).• Place the blank (#1) into t

64 65Iodine• Reinsert the cuvette into the instrument.• Press Timer and the display will show the countdown prior to the measurement or, alternatively

66 67Iron HR• Reinsert the cuvette into the instrument.• Press Timer and the display will show the countdown prior to the measurement or, alternativel

68 69Iron LR• Press the Zero key. The display will show “-0.0-” when the meter is zeroed and ready formeasurement.• Remove the cuvette.• Fill another

70 71MagnesiumSPECIFICATIONSRange 0 to 150 mg/LResolution 5 mg/LAccuracy ±5 mg/L ±3% of reading at 25 °CLight Source Tungsten lamp with narrow band in

72 73SPECIFICATIONSRange 0.0 to 20.0 mg/LResolution 0.1 mg/LAccuracy ±0.2 mg/L ±3% of reading at 25 °CTypical EMC ±0.1 mg/LDeviationLight Source Tungs

74 75Manganese LRMANGANESE LOW RANGESPECIFICATIONSRange 0 to 300 µg/LResolution 1 µg/LAccuracy ±10 µg/L ±3% of reading at 25 °CTypical EMC ±1 µg/LDevi

76 77Manganese LR• Insert the second cuvette with the reacted sample into the instrument.• Press Read to start the reading. The instrument displays th

6 7INSTRUMENT DESCRIPTIONKEYPAD DESCRIPTIONThe keypad contains 8 direct keys and 3 functional keys with the following functions:Press to perform the f

78 79• Fill one graduated mixing cylinder up to the 25 mLmark with the sample.• Add the content of one packet of HI 93730A-0molybdenum reagent, close

80 81Nickel HRSPECIFICATIONSRange 0.00 to 7.00 g/LResolution 0.01 g/LAccuracy ±0.07 ±4% of reading at 25 °CTypical EMC ±0.02 g/LDeviationLight Source

82 83 Nickel LRNICKEL LOW RANGESPECIFICATIONSRange 0.000 to 1.000 mg/LResolution 0.001 mg/LAccuracy ±0.010 mg/L ±7% of reading at 25 °CTypical EMC ±0.

84 85INTERFERENCESInterference may be caused by:Co2+ must not be presentFe2+ must not be presentAl3+ above 32 mg/LCa2+ above 1000 mg/L (as CaCO3)Cd2+

86 87 Nitrate• Replace the cap and immediately shake vigorously upand down for exactly 10 seconds. Continue to mix byinverting the cuvette gently for

88 89Nitrite HR• Add the content of one packet of HI 93708-0 reagent.Replace the cap and shake gently until completely dissolved.• Reinsert the cuvett

90 91• Reinsert the cuvette into the instrument.• Press Timer and the display will show the countdown prior to the measurement or, alternatively, wait

92 93Dissolved Oxygen• Let the sample stand and the flocculent agent will start to settle.• After approximately 2 minutes, when the upper half of the

94 95Ozone• Press the Zero key. The display will show “-0.0-” the meter is zeroed and ready for measurement.• Remove the cuvette.• Add the content of

96 97pHpHSPECIFICATIONSRange 6.5 to 8.5 pHResolution 0.1 pHAccuracy ±0.1 pH at 25 °CTypical EMC ±0.1 pHDeviationLight Source Tungsten lamp with narrow

8 9(c)(a) (b)Probable level ofliquid taken upby syringeThe instructions listed below should be carefully followed during testing to ensure most accura

98 99Phosphate HRPHOSPHATE HIGH RANGESPECIFICATIONSRange 0.0 to 30.0 mg/LResolution 0.1 mg/LAccuracy ±1 mg/L ±4% of reading at 25 °CTypical EMC Dev. ±

100 101Phosphate LRPHOSPHATE LOW RANGESPECIFICATIONSRange 0.00 to 2.50 mg/LResolution 0.01 mg/LAccuracy ±0.04 mg/L ±4% of reading at 25 °CTypical EMC

102 103PhosphorusPHOSPHORUSSPECIFICATIONSRange 0.0 to 15.0 mg/LResolution 0.1 mg/LAccuracy ±0.3 mg/L ±4% of reading at 25 °CTypical EMC Dev. ±0.2 mg/L

104 105Potassium HRPOTASSIUM HIGH RANGESPECIFICATIONSRange 20 to 200 mg/LResolution 5 mg/LAccuracy ±30 mg/L ±7% of reading at 25 °CTypical EMC ±5 mg/L

106 107Potassium HRPOTASSIUM ULTRA HIGH RANGEFor samples containing more than 200 ppm of Potassium: follow the sample preparation proceduredescribed a

108 109• Press the Zero key. The display will show “-0.0-” when the meter is zeroed and ready for measurement.• Remove the cuvette and add the content

110 111• Press the Zero key. The display will show “-0.0-” when the meter is zeroed and ready for measurement.• Remove the cuvette and add the content

112 113Silica• Press the Zero key. The display will show “-0.0-” when the meter is zeroed and ready for measurement.• Remove the cuvette and add the c

114 115Silver• Add exactly 1.0 mL of HI 93737B-0 Buffer reagent to the secondbeaker (the sample) and swirl gently to mix. Press Timer and thedisplay w

116 117SPECIFICATIONSRange 0 to 100 mg/LResolution 5 mg/LAccuracy ±5 mg/L ±3% of reading at 25 °CLight Source Tungsten lamp with narrow band interfere

10 11• Pay attention to push the cuvette completely down in the holder and to align the white point on thecap to the indexing mark on the meter.• In o

118 119ZincZINCSPECIFICATIONSRange 0.00 to 3.00 mg/LResolution 0.01 mg/LAccuracy ±0.03 mg/L ±3% of reading at 25 °CTypical EMC ±0.01 mg/LDeviationLigh

120 121The instrument shows clear warning messages when erroneous conditions appear and when measured values areoutside the expected range. These mess

122 123Description Range MethodAluminum 0.00 to 1.00 mg/L AluminonAlkalinity 0 to 500 mg/L ColorimetricAmmonia MR 0.00 to 10.00 mg/L NesslerAmmonia LR

124 125HI 93722-01 100 cyanuric acid testsHI 93722-03 300 cyanuric acid testsHI 93723-01 100 chromium VI HR testsHI 93723-03 300 chromium VI HR testsH

126 127WARRANTYAll Hanna Instruments meters are warranted for two years against defects in workmanship and materialswhen used for its intended purpose

128Printed in EUROPE(ROMANIA)Hanna Instruments Inc.Highland Industrial Park584 Park East DriveWoonsocket, RI 02895 USATechnical Support for CustomersT

12 13POWER CONNECTION AND BATTERY MANAGEMENTThe meter can be powered from an AC/DC adapter (included) or from the built-in rechargeable battery.Note:

14 15Date / TimeThis option is used to set the instrument’s date and time.Press the Modify key to change the date/time.Press the ⊳ u functional keys t

16 17HI 83200 offers an interactive contextual help mode that assists the user at any time.To access the help screens press HELP.The instrument will d